S4 B8.5, S6 Audi heat exchanger convenience install pack
$38.00
This product is not compatible with the old heat exchanger (original version)
99952 in stock (can be backordered)
-
Save time running to the stores and use these higher quality components not found easily on local stores. This kit is to facilitate the installation when upgrading from the Audi OEM heat exchanger system.
- 16 inches of 3/4″ High-quality hose (not cheap rubber hose)
- 6 All stainless steel clamps (these will not rust)
- 2 straight billet aluminum 3/4″ hose connectors
**The heat exchanger already has brackets and mounting bolts.
| Weight | 2 lbs |
|---|---|
| Dimensions | 8 × 3 × 2 in |
You must be logged in to post a review.
You may also like…
Related products
- Quick ViewSale!
034MOTORSPORT FRONT STRUT BRACE, B8 AUDI A4/S4, ALLROAD, BILLET ALUMINUM
$359.00Read more034Motorsport is proud to offer our Billet Aluminum Front Strut Brace for the B8 Audi A4/S4 & Allroad! These Audi models do not come with a strut brace from the factory, allowing for lateral deflection of the strut towers and chassis flex under hard cornering. While the B8 chassis comes from the factory with a support bar located behind the fire wall, this component is not significantly structural to the chassis and allows strut tower deflection. This deflection can be observed as imprecise steering input and a vague, disconnected feeling from the front end due to undesired suspension geometry changes.
The 034Motorsport Strut Brace incorporates an extremely rigid billet aluminum center section that attaches to both strut towers and to the firewall in two locations, improving the vehicle’s steering feel and handling performance. This robust chassis reinforcement is machined from 6061-T6 billet aluminum, and engineered to be a comprehensive upgrade by limiting lateral strut tower deflection and maintaining proper suspension geometry under heavy cornering. The end result is a significantly more rigid front end that provides precise, consistent feedback through the steering wheel and ensures that you enjoy a more connected driving experience.
This strut brace was thoroughly tested by 034Motorsport on in-house B8 and B8.5 Audi S4 Development Vehicles before release.
FEATURES:
- Truss Design is Lightweight and Extremely Rigid
- 6061-T6 Billet Aluminum Construction with Clear Anodized Finish
- Attaches to Both Strut Towers and the Firewall in Two Locations
- Engineered to Enhance Handling Dynamics and Performance
- Improves Steering Feel, Consistency, and Precision
WHAT’S INCLUDED:
- 034Motorsport Billet Aluminum Front Strut Brace Chassis Reinforcement
- Strut Tower Brackets
- Strut Bar Brackets
- Transfer Punch
- Transfer Punch Guides (4)
- Mounting Hardware
- Quick View
Audi divorce kit DIY components
$46.00Add to cartThese parts are specifically made for the MercRacing heat exchangers. Fitting for the heat exchanger bleed port 5 feet silicone hose for the heat exchanger to reservoir bleed port setup Flow control valve Billet T fitting for reservoir fill tank. Reinforced silicone cap for coolant system divorce operation. Click here for > INSTALLATION INFORMATION
- Quick View
MercRacing 3.0TFSI SUPERCHARGER BLEEDER SCREW KIT FOR AUDI B8/B8.5/C7/D4 S4/S5/Q5/SQ5/A6/A7/A8
$28.00Add to cartReplace those failure-prone, plastic 3.0 TFSI supercharger bleeder screws with the MercRacing 3.0 TFSI Supercharger Bleeder Screw Kit for Aud B8/B8.5/C7/D4 S4/S5/Q5/SQ5/A6/A7/A8 vehicles. The OEM bleeder screws are not designed for multiple uses and the soft plastic can easily be damaged to the point where they no longer can be loosened or tightened. These CNC …
Reviews
There are no reviews yet.